Editing Wpa cli

Jump to navigation Jump to search

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
−
{{lowercase}}
+
−
wpa_cli is a command for interacting with <code>[[wpa_supplicant]]</code>.
+
wpa_cli -i wlp6s0 list_sta
−
* https://linux.die.net/man/8/wpa_cli
+
wpa_cli -i wlp6s0 all_sta
 +
 
 +
wpa_cli -I wlp6s0 log_level debug
 +
 
 +
[[wpa_cli wlan0 status]]
 +
 
 +
[[wpa_cli -i wlan0 get capability key mgmt]]
 +
 
 +
wpa_cli -i wlp6s0 scan_results
 +
bssid / frequency / signal level / flags / ssid
 +
 
 +
 
 +
wpa_cli help
 +
Selected interface 'p2p-dev-wlp6s0'
 +
commands:
 +
  status [verbose] = get current WPA/EAPOL/EAP status
 +
  ifname = get current interface name
 +
  ping = pings wpa_supplicant
 +
  relog = re-open log-file (allow rolling logs)
 +
  note <text> = add a note to wpa_supplicant debug log
 +
  mib = get MIB variables (dot1x, dot11)
 +
  help [command] = show usage help
 +
  interface [ifname] = show interfaces/select interface
 +
  level <debug level> = change debug level
 +
  license = show full wpa_cli license
 +
  quit = exit wpa_cli
 +
  set = set variables (shows list of variables when run without arguments)
 +
  dump = dump config variables
 +
  get <name> = get information
 +
  driver_flags = list driver flags
 +
  logon = IEEE 802.1X EAPOL state machine logon
 +
  logoff = IEEE 802.1X EAPOL state machine logoff
 +
    pmksa = show PMKSA cache
 +
  pmksa_flush = flush PMKSA cache entries
 +
  pmksa_get <network_id> = fetch all stored PMKSA cache entries
 +
  pmksa_add <network_id> <BSSID> <PMKID> <PMK> <reauth_time in seconds> <expiration in seconds> <akmp> <opportunistic> = store PMKSA cache entry from external storage
 +
  reassociate = force reassociation
 +
  reattach = force reassociation back to the same BSS
 +
  preauthenticate <BSSID> = force preauthentication
 +
  identity <network id> <identity> = configure identity for an SSID
 +
  password <network id> <password> = configure password for an SSID
 +
  new_password <network id> <password> = change password for an SSID
 +
  pin <network id> <pin> = configure pin for an SSID
 +
  otp <network id> <password> = configure one-time-password for an SSID
 +
  psk_passphrase <network id> <PSK/passphrase> = configure PSK/passphrase for an SSID
 +
  passphrase <network id> <passphrase> = configure private key passphrase
 +
    for an SSID
 +
  sim <network id> <pin> = report SIM operation result
 +
  bssid <network id> <BSSID> = set preferred BSSID for an SSID
 +
  blacklist <BSSID> = add a BSSID to the blacklist
 +
  blacklist clear = clear the blacklist
 +
  blacklist = display the blacklist
 +
  log_level <level> [<timestamp>] = update the log level/timestamp
 +
  log_level = display the current log level and log options
 +
  list_networks = list configured networks
 +
  select_network <network id> = select a network (disable others)
 +
  enable_network <network id> = enable a network
 +
  disable_network <network id> = disable a network
 +
  add_network = add a network
 +
  remove_network <network id> = remove a network
 +
  set_network <network id> <variable> <value> = set network variables (shows
 +
    list of variables when run without arguments)
 +
  get_network <network id> <variable> = get network variables
 +
  dup_network <src network id> <dst network id> <variable> = duplicate network variables
 +
  list_creds = list configured credentials
 +
  add_cred = add a credential
 +
  remove_cred <cred id> = remove a credential
 +
  set_cred <cred id> <variable> <value> = set credential variables
 +
  get_cred <cred id> <variable> = get credential variables
 +
  save_config = save the current configuration
 +
  disconnect = disconnect and wait for reassociate/reconnect command before
 +
    connecting
 +
  reconnect = like reassociate, but only takes effect if already disconnected
 +
  scan = request new BSS scan
 +
  scan_results = get latest scan results
 +
  abort_scan = request ongoing scan to be aborted
 +
  bss <<idx> | <bssid>> = get detailed scan result info
 +
  get_capability <eap/pairwise/group/[[wpa_cli -i wlan0 get_capability key_mgmt|key_mgmt]]/proto/auth_alg/channels/freq/modes> = get capabilities
 +
  reconfigure = force wpa_supplicant to re-read its configuration file
 +
  terminate = terminate wpa_supplicant
 +
  interface_add <ifname> <confname> <driver> <ctrl_interface> <driver_param>
 +
    <bridge_name> <create> <type> = adds new interface, all parameters but
 +
    <ifname> are optional. Supported types are station ('sta') and AP ('ap')
 +
  interface_remove <ifname> = removes the interface
 +
  interface_list = list available interfaces
 +
  ap_scan <value> = set ap_scan parameter
 +
  scan_interval <value> = set scan_interval parameter (in seconds)
 +
  bss_expire_age <value> = set BSS expiration age parameter
 +
  bss_expire_count <value> = set BSS expiration scan count parameter
 +
  bss_flush <value> = set BSS flush age (0 by default)
 +
  ft_ds <addr> = request over-the-DS FT with <addr>
 +
  wps_pbc [BSSID] = start Wi-Fi Protected Setup: Push Button Configuration
 +
  wps_pin <BSSID> [PIN] = start WPS PIN method (returns PIN, if not hardcoded)
 +
  wps_check_pin <PIN> = verify PIN checksum
 +
  wps_cancel Cancels the pending WPS operation
 +
  wps_nfc [BSSID] = start Wi-Fi Protected Setup: NFC
 +
  wps_nfc_config_token <WPS|NDEF> = build configuration token
 +
  wps_nfc_token <WPS|NDEF> = create password token
 +
  wps_nfc_tag_read <hexdump of payload> = report read NFC tag with WPS data
 +
  nfc_get_handover_req <NDEF> <WPS> = create NFC handover request
 +
  nfc_get_handover_sel <NDEF> <WPS> = create NFC handover select
 +
  nfc_report_handover <role> <type> <hexdump of req> <hexdump of sel> = report completed NFC handover
 +
  wps_reg <BSSID> <AP PIN> = start WPS Registrar to configure an AP
 +
  wps_ap_pin [params..] = enable/disable AP PIN
 +
  wps_er_start [IP address] = start Wi-Fi Protected Setup External Registrar
 +
  wps_er_stop = stop Wi-Fi Protected Setup External Registrar
 +
  wps_er_pin <UUID> <PIN> = add an Enrollee PIN to External Registrar
 +
  wps_er_pbc <UUID> = accept an Enrollee PBC using External Registrar
 +
  wps_er_learn <UUID> <PIN> = learn AP configuration
 +
  wps_er_set_config <UUID> <network id> = set AP configuration for enrolling
 +
  wps_er_config <UUID> <PIN> <SSID> <auth> <encr> <key> = configure AP
 +
  wps_er_nfc_config_token <WPS/NDEF> <UUID> = build NFC configuration token
 +
  ibss_rsn <addr> = request RSN authentication with <addr> in IBSS
 +
  sta <addr> = get information about an associated station (AP)
 +
  all_sta = get information about all associated stations (AP)
 +
  list_sta = list all stations (AP)
 +
  deauthenticate <addr> = deauthenticate a station
 +
  disassociate <addr> = disassociate a station
 +
  chan_switch <cs_count> <freq> [sec_channel_offset=] [center_freq1=] [center_freq2=] [bandwidth=] [blocktx] [ht|vht] = CSA parameters
 +
  suspend = notification of suspend/hibernate
 +
  resume = notification of resume/thaw
 +
  roam <addr> = roam to the specified BSS
 +
  p2p_find [timeout] [type=*] = find P2P Devices for up-to timeout seconds
 +
  p2p_stop_find = stop P2P Devices search
 +
  p2p_asp_provision <addr> adv_id=<adv_id> conncap=<conncap> [info=<infodata>] = provision with a P2P ASP Device
 +
  p2p_asp_provision_resp <addr> adv_id=<adv_id> [role<conncap>] [info=<infodata>] = provision with a P2P ASP Device
 +
  p2p_connect <addr> <"pbc"|PIN> [ht40] = connect to a P2P Device
 +
  p2p_listen [timeout] = listen for P2P Devices for up-to timeout seconds
 +
  p2p_group_remove <ifname> = remove P2P group interface (terminate group if GO)
 +
  p2p_group_add [ht40] = add a new P2P group (local end as GO)
 +
  p2p_group_member <dev_addr> = Get peer interface address on local GO using peer Device Address
 +
  p2p_prov_disc <addr> <method> = request provisioning discovery
 +
  p2p_get_passphrase = get the passphrase for a group (GO only)
 +
  p2p_serv_disc_req <addr> <TLVs> = schedule service discovery request
 +
  p2p_serv_disc_cancel_req <id> = cancel pending service discovery request
 +
  p2p_serv_disc_resp <freq> <addr> <dialog token> <TLVs> = service discovery response
 +
  p2p_service_update = indicate change in local services
 +
  p2p_serv_disc_external <external> = set external processing of service discovery
 +
  p2p_service_flush = remove all stored service entries
 +
  p2p_service_add <bonjour|upnp|asp> <query|version> <response|service> = add a local service
 +
  p2p_service_rep asp <auto> <adv_id> <svc_state> <svc_string> [<svc_info>] = replace local ASP service
 +
  p2p_service_del <bonjour|upnp> <query|version> [|service] = remove a local service
 +
  p2p_reject <addr> = reject connection attempts from a specific peer
 +
  p2p_invite <cmd> [peer=addr] = invite peer
 +
  p2p_peers [discovered] = list known (optionally, only fully discovered) P2P peers
 +
  p2p_peer <address> = show information about known P2P peer
 +
  p2p_set <field> <value> = set a P2P parameter
 +
  p2p_flush = flush P2P state
 +
  p2p_cancel = cancel P2P group formation
 +
  p2p_unauthorize <address> = unauthorize a peer
 +
  p2p_presence_req [<duration> <interval>] [<duration> <interval>] = request GO presence
 +
  p2p_ext_listen [<period> <interval>] = set extended listen timing
 +
  p2p_remove_client <address|iface=address> = remove a peer from all groups
 +
  vendor_elem_add <frame id> <hexdump of elem(s)> = add vendor specific IEs to frame(s)
 +
    0: Probe Req (P2P), 1: Probe Resp (P2P) , 2: Probe Resp (GO), 3: Beacon (GO), 4: PD Req, 5: PD Resp, 6: GO Neg Req, 7: GO Neg Resp, 8: GO Neg Conf, 9: Inv Req, 10: Inv Resp, 11: Assoc Req (P2P), 12: Assoc Resp (P2P)
 +
  vendor_elem_get <frame id> = get vendor specific IE(s) to frame(s)
 +
    0: Probe Req (P2P), 1: Probe Resp (P2P) , 2: Probe Resp (GO), 3: Beacon (GO), 4: PD Req, 5: PD Resp, 6: GO Neg Req, 7: GO Neg Resp, 8: GO Neg Conf, 9: Inv Req, 10: Inv Resp, 11: Assoc Req (P2P), 12: Assoc Resp (P2P)
 +
  vendor_elem_remove <frame id> <hexdump of elem(s)> = remove vendor specific IE(s) in frame(s)
 +
    0: Probe Req (P2P), 1: Probe Resp (P2P) , 2: Probe Resp (GO), 3: Beacon (GO), 4: PD Req, 5: PD Resp, 6: GO Neg Req, 7: GO Neg Resp, 8: GO Neg Conf, 9: Inv Req, 10: Inv Resp, 11: Assoc Req (P2P), 12: Assoc Resp (P2P)
 +
  wfd_subelem_set <subelem> [contents] = set Wi-Fi Display subelement
 +
  wfd_subelem_get <subelem> = get Wi-Fi Display subelement
 +
  fetch_anqp = fetch ANQP information for all APs
 +
  stop_fetch_anqp = stop fetch_anqp operation
 +
  interworking_select [auto] = perform Interworking network selection
 +
  interworking_connect <BSSID> = connect using Interworking credentials
 +
  interworking_add_network <BSSID> = connect using Interworking credentials
 +
  anqp_get <addr> <info id>[,<info id>]... = request ANQP information
 +
  gas_request <addr> <AdvProtoID> [QueryReq] = GAS request
 +
  gas_response_get <addr> <dialog token> [start,len] = Fetch last GAS response
 +
  hs20_anqp_get <addr> <subtype>[,<subtype>]... = request HS 2.0 ANQP information
 +
  nai_home_realm_list <addr> <home realm> = get HS20 nai home realm list
 +
  hs20_icon_request <addr> <icon name> = get Hotspot 2.0 OSU icon
 +
  fetch_osu = fetch OSU provider information from all APs
 +
  cancel_fetch_osu = cancel fetch_osu command
 +
  sta_autoconnect <0/1> = disable/enable automatic reconnection
 +
  tdls_discover <addr> = request TDLS discovery with <addr>
 +
  tdls_setup <addr> = request TDLS setup with <addr>
 +
  tdls_teardown <addr> = tear down TDLS with <addr>
 +
  tdls_link_status <addr> = TDLS link status with <addr>
 +
  wmm_ac_addts <uplink/downlink/bidi> <tsid=0..7> <up=0..7> [nominal_msdu_size=#] [mean_data_rate=#] [min_phy_rate=#] [sba=#] [fixed_nominal_msdu] = add WMM-AC traffic stream
 +
  wmm_ac_delts <tsid> = delete WMM-AC traffic stream
 +
  wmm_ac_status = show status for Wireless Multi-Media Admission-Control
 +
  tdls_chan_switch <addr> <oper class> <freq> [sec_channel_offset=] [center_freq1=] [center_freq2=] [bandwidth=] [ht|vht] = enable channel switching with TDLS peer
 +
  tdls_cancel_chan_switch <addr> = disable channel switching with TDLS peer <addr>
 +
  signal_poll = get signal parameters
 +
  signal_monitor = set signal monitor parameters
 +
  pktcnt_poll = get TX/RX packet counters
 +
  reauthenticate = trigger IEEE 802.1X/EAPOL reauthentication
 +
  autoscan [params] = Set or unset (if none) autoscan parameters
 +
  raw <params..> = Sent unprocessed command
 +
  flush = flush wpa_supplicant state
 +
  radio_work = radio_work <show/add/done>
 +
  vendor <vendor id> <command id> [<hex formatted command argument>] = Send vendor command
 +
  neighbor_rep_request [ssid=<SSID>] [lci] [civic] = Trigger request to AP for neighboring AP report (with optional given SSID in hex or enclosed in double quotes, default: current SSID; with optional LCI and location civic request)
 +
  erp_flush = flush ERP keys
 +
  mac_rand_scan <scan|sched|pno|all> enable=<0/1> [addr=mac-address mask=mac-address-mask] = scan MAC randomization
 +
  get_pref_freq_list <interface type> = retrieve preferred freq list for the specified interface type
 +
  p2p_lo_start <freq> <period> <interval> <count> = start P2P listen offload
 +
  p2p_lo_stop = stop P2P listen offload
 +
  dpp_qr_code report a scanned DPP URI from a QR Code
 +
  dpp_bootstrap_gen type=<qrcode> [chan=..] [mac=..] [info=..] [curve=..] [key=..] = generate DPP bootstrap information
 +
  dpp_bootstrap_remove *|<id> = remove DPP bootstrap information
 +
  dpp_bootstrap_get_uri <id> = get DPP bootstrap URI
 +
  dpp_bootstrap_info <id> = show DPP bootstrap information
 +
  dpp_auth_init peer=<id> [own=<id>] = initiate DPP bootstrapping
 +
  dpp_listen <freq in MHz> = start DPP listen
 +
  dpp_stop_listen = stop DPP listen
 +
  dpp_configurator_add [curve=..] [key=..] = add DPP configurator
 +
  dpp_configurator_remove *|<id> = remove DPP configurator
 +
  dpp_configurator_get_key <id> = Get DPP configurator's private key
 +
  dpp_configurator_sign conf=<role> configurator=<id> = generate self DPP configuration
 +
  dpp_pkex_add add PKEX code
 +
  dpp_pkex_remove *|<id> = remove DPP pkex information
 +
</pre>
  
−
== Examples ==
 
−
* <code>[[wpa_cli help]]</code>
 
−
* <code>[[wpa_cli wlan0 status]]</code>
 
−
* <code>[[wpa_cli wlan0 dump]]</code>
 
−
* <code>wpa_cli -i [[wlp]]6s0 [[list_sta]]</code>
 
−
* <code>wpa_cli -i wlp6s0 [[all_sta]]</code>
 
−
* <code>[[wpa_cli -i wlan0 log_level]] debug</code>
 
−
* <code>[[wpa_cli -i wlan0 get capability key mgmt]]</code>
 
−
* <code>wpa_cli -i wlp6s0 scan_results</code>
 
  
 
== See also ==
 
== See also ==
−
* {{wpa_cli}}
 
 
* {{iw}}
 
* {{iw}}
 
* {{wifi}}
 
* {{wifi}}
  
 
[[Category:WiFi]]
 
[[Category:WiFi]]

Please note that all contributions to wikieduonline may be edited, altered, or removed by other contributors. If you do not want your writing to be edited mercilessly, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource (see Wikieduonline:Copyrights for details). Do not submit copyrighted work without permission!

Cancel Editing help (opens in new window)

Templates used on this page:

Retrieved from "https://www.wikieduonline.com/wiki/Wpa_cli"

Advertising: