Difference between revisions of "Ethtool"

From wikieduonline
Jump to navigation Jump to search
Line 4: Line 4:
 
  ethtool -K eth0 [[gso]] off [[gro]] off [[tso]] off
 
  ethtool -K eth0 [[gso]] off [[gro]] off [[tso]] off
  
* Disable [[TCP]] checksum offloading
+
* Disable [[TCP checksum]] offloading
 
  ethtool -K eth0 tx off rx off
 
  ethtool -K eth0 tx off rx off
  

Revision as of 13:00, 22 November 2020

ethtool[1] command is used to view and modify network device drivers setting, in particular wired Ethernet devices.


ethtool -K eth0 gso off gro off tso off
ethtool -K eth0 tx off rx off

Examples

 Settings for eno1:
 	Supported ports: [ TP ]
	Supported link modes:   10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	                        1000baseT/Half 1000baseT/Full
	Supported pause frame use: No
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	                        1000baseT/Half 1000baseT/Full
	Advertised pause frame use: Symmetric
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  10baseT/Half 10baseT/Full
	                                     100baseT/Half 100baseT/Full
	                                     1000baseT/Full
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported
	Speed: 1000Mb/s
	Duplex: Full
	Port: Twisted Pair
	PHYAD: 4
	Transceiver: internal
	Auto-negotiation: on
	MDI-X: off
	Supports Wake-on: g
	Wake-on: g
	Current message level: 0x000000ff (255)
			       drv probe link timer ifdown ifup rx_err tx_err
        Link detected: yes
ethtool eno1
Settings for eno1:
	Supported ports: [ TP ]
	Supported link modes:   10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	                        1000baseT/Full
	Supported pause frame use: No
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	                        1000baseT/Full
	Advertised pause frame use: No
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Speed: 1000Mb/s
	Duplex: Full
	Port: Twisted Pair
	PHYAD: 1
	Transceiver: internal
	Auto-negotiation: on
	MDI-X: off (auto)
	Supports Wake-on: pumbg
	Wake-on: g
	Current message level: 0x00000007 (7)
			       drv probe link
	Link detected: yes
ethtool ens3f1
Settings for ens3f1:
	Supported ports: [ ]
	Supported link modes:   1000baseT/Full
	                        1000baseKX/Full
	                        10000baseT/Full
	                        1000baseX/Full
	                        10000baseSR/Full
	                        10000baseLR/Full
	Supported pause frame use: Symmetric
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  1000baseT/Full
	                        1000baseKX/Full
	                        10000baseT/Full
	                        1000baseX/Full
	                        10000baseSR/Full
	                        10000baseLR/Full
	Advertised pause frame use: No
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Speed: Unknown!
	Duplex: Unknown! (255)
	Port: Other
	PHYAD: 0
	Transceiver: internal
	Auto-negotiation: off
	Supports Wake-on: d
	Wake-on: d
	Current message level: 0x00000007 (7)
			       drv probe link
	Link detected: no
ethtool -i eno1
driver: e1000e
version: 3.2.6-k
firmware-version: 0.5-4
expansion-rom-version:
bus-info: 0000:00:1f.6
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no

Related terms

See also

  • http://man7.org/linux/man-pages/man8/ethtool.8.html
  • Advertising: